Upcoming shows/vending:






 Know of a show I should go to? Tell me!

Porta Pi Arcade10" Vertical [SHMUP]

A carbon copy of Porta Pi Arcade with the exception of the LCD orientation. Relive the classic era of 1980's arcades with the [almost] properly proportioned vertical cabinet. Since modern TFT LCDs are 16:10 (well this one is), vertial oriented arcade games will not fully fill the screen without some non-native ratio stretching. Cabinet measures ~16 x 10 x 9.5 inches (H x W x D). The side buttons and 2 control panel buttons have been removed (with respect to the Porta Pi Arcade 10" cabinet). There are four 28mm arcade buttons holes with an additional two 12mm button holes located below the marquee. Joystick can be either Suzo Happ or Sanwa. 


This kit is a DIY kit that turns your Raspberry Pi (Model B, B+, Pi2, Pi3), or other tiny computer, in a fully functional Mini ArcadeThe wood is underlaminate plywood. This wood takes paint well, but proper sanding, filling, priming and painting will result in the best look.


Don't want to use a Raspberry Pi? The cabinet can accommodate small, older video game consoles or single board computers. The joystick and buttons can be hard-wired to the console's controller turning it into a dedicated unit. Or, fit a mini-ITX motherboard or ultra-compact PC inside and it becomes a super powered mini PC arcade. You can also fit a small JAMMA PCB inside, small PCBs like the 60-in-1 boards found on ebay. 


This kit fits the Raspberry Pi B (512MB rev 2) B+, Pi 2, and Pi 3 models.


Wood Kit Includes:

  • Precision Laser Cut Cabinet: overall size/footprint: 15.75 x 10 x 9.5 inches (HxWxD)


Raspberry Pi, micro SD Card (8GB+ is recommended), the RPi's respective power cable (micro usb) and EVERYTHING ELSE (arcade parts, LCD, misc wires buttons, power supply).



Kit Types:

Wood Panel Kit

Wood panels only. For the motivated builder.



Optional Parts

Clear acrylic for the marquee, LCD bezel, and control panel. Good for protecting your paint/artwork from heavy use. Also completes the look.

Note: Be sure to select the correct cabinet model from the drop down menu below. I have one button containing all acrylic cabinet model add-ons, make sure you pick the appropriate model for your cabinet. 

Go to Arcade Parts page and add to cart.

Using a 12V supply? Check out the Power Block Arcade for easy wiring + a stepdown converter.

Assembly Guide

Read and watch the Porta Pi Arcade Assembly Manual and Video. With that knowledge in the back of your head, you only need to be aware of a few caveats when assembling the cabinet.

1) The Marquee panel is asymmetrical (shown in orange) on the horizontal axis. See the photos below. Do not install it upside down, if you do and you backlit the marquee you'll have a shadow over half of it. The top of the panel will also be slightly short of covering the top of the arcade.

2) The L brackets (shown in red) that hold the LCD in place have only one lip on them. This lip should be on the bottom.

Legal Stuff. (because reasons)


Under no circumstances will Retro Built Games, LLC or Ryan Bates be responsible for any loss or damages, including personal injury or death, that may results from your engagement in the activity demonstrated in the affilated videos, website or related documentation. You also assume all risk and liability that may result in such activities. Retro Built Games, LLC disclaims all warranties.

Copyright (c) 2016 Ryan Bates. All rights reserved.
Copyright (c) 2016  Retro Built Games, LLC. All rights reserved.

No part of this website may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of the publisher.

The software mentioned in this how-to holds copyrights by its respective authors. Said software is "AS IS" and should be downloaded, installed, and used at your own risk. Ryan Bates and Retro Built Games, LLC disclaims all warranties of any kind, either express or implied, as to the software, including, but not limited to, losses, damages, claims or costs including and indirect, consequential, or incidental damages, any lost profits or lost savings, personal injury even if  Ryan Bates or Retro Built Games, LLC has been advised of the possibility of such loss, damages, claims, or cost.

Under no circumstances shall Retro Built Games, LLC or Ryan Bates be liable to any user for direct, indirect, incidental, consequential, special, or exemplary damages, arising from or relating to this agreement, the software, or user's use or misuse of the software or hardware.

Neither this agreement nor any documentation furnished under it is intended to express or imply any warranty that the operation of this compilation of software will be uninterrupted, functional, or error‐free. I tend to make a few typos.

Retro Built Games reserves the right to make any changes to the kit design, or supplied kit items or materials without notice. Actual item may differ from shown pictures. Read the entire page carefully as these changes are documented in the appropriate areas.

Changed your mind? All Arcade kit returns are subject to a 20% restocking fee once shipped. If not shipped you will receive a full refund.



Print | Sitemap
© 2013-2023 Ryan Bates and © 2013-2023 Retro Built Games, LLC. All photos, designs, documents, and graphics (C) Ryan Bates. All Rights Reserved.

This site is best viewed on a desktop PC. (Can't find the payment buttons? Use a desktop web browser or Request Desktop Site) Raspberry Pi is a trademark of the Raspberry Pi Foundation. ARDUINO® and other Arduino brands and logos published in the website are Trademarks of Arduino AG.